Woodworking Technician

Select start date and campus

Applying as a Canadian applicant

Domestic students should apply online or by phone at 1-888-892-2228.

Applying as an International applicant

International students should apply online.

Campus tours

Campus tours are one of the best ways to experience Conestoga. During this time, we are offering online guided tours to show you all Conestoga has to offer.

Book your tour

Virtual tours

If you can't make an on-campus tour or attend one of our events, the virtual tour is a great way to visit us.

View our Virtual tour

Academic handbook

This handbook provides students with important information relating to their academic journey. The material in this handbook is accurate at the date of posting and is applicable for the current academic year. Academic school handbooks are updated yearly and students must check for the current edition.

View handbook

Program Advisory Committee (PAC)

PAC members are composed of employers, practitioners and recent program graduates. College representatives (students, faculty, and administrators) are resource persons. Each committee advises the Board on the development of new programs, the monitoring of existing programs and community acceptance of programs.

View advisors

Success stories

November 1, 2024

Go ENG Girl introduces girls and non-binary youth to the diverse world of engineering

October 20, 2024

Conestoga celebrates class of 2024 at fall convocation

October 5, 2024

Homecoming welcomes APFM degree program students, alumni and faculty

September 27, 2024

Interior Design students win top prizes in student design competition

Explore our campus & labs

Student supplied toolkits

PPE (Personal Protective Equipment)

Safety boots or shoes (CSA Approved)
Safety glasses (CSA Approved) or goggles over prescription eyewear
Hearing protection (optional)

Tools for term 1 (approximately $300)

Pocket calculator (For MATH1227 course and shop use)
Combination Imperial & Metric tape measure (10' preferred)
Paint / wood scraper (minimum 9” length, pull type)
Block plane
Set of chisels (long shanks): 1/4", 1/2", & 3/4"
Dovetail saw (fine tooth point preferred)
Combination square (45° - 90°), (metal preferred)
Sharpening stone; combination fine (1000grit) / superfine (4000 grit) water stone
Hammer - 10 to 16 oz.
Screwdriver sets: Robertson (3 sizes; red #8, green #6 & yellow #4), Phillips (#1, #2) Slot (2 sizes)
Driver bits for Robertson #4, #6, and #8 screws (2” length preferred)
1 1/4" putty knife (metal preferred)
Utility knife
Set of High Speed Steel drill bits (1/16" to 3/8") (Brad point tips preferred)
4" C clamps, minimum quantity of 2
8 GB - 32 GB USB Drive
Portable tool box (20” to 22”), plastic or metal, and lock (so the box can be locked in the shop)

Additional tools for term 2 (approximately $100)

Set of Allen keys – Metric (1.5mm to 10mm) & Imperial (1/16” to 3/8”), short or long arm
Vernier calipers – combination Metric and Imperial
2- or 3-piece Nail punch set
Adjustable wrench (6” or 8” length preferred)
Cabinet scraper (looks like a rectangular piece of spring steel)
Needle nose pliers (6” or 8” length preferred)

Additional tools for term 3 (approximately $100)

Rolls of 3/4" or 1" masking tape (student repurchases as required)
Set of Counter sink bits for Robertson #6 and #8 size screws
Vix-bits (self-centering bits for Robertson #6 & #8 size screws)
Side cutting pliers (6” length preferred)
Chanel lock pliers (9” to 10” length preferred)
Rubber mallet -16 to 32 oz. (white, non-marring preferred)

Note: Please keep all tool receipts in case of exchange after consulting with your instructor.